ISO INTERNATIONAL STANDARD 363-1 First edition 2006-03-15 Textile machinery and accessories Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled steel wire MaterielpourI'industrietextile-Lisses en acierplatavecboucles d'extremitesfermees Partie 1:Dimensions des lisses fabriquees enfils d'acierlamine Reference number ISO 363-1:2006(E) @ISO2006 Copyright Intern ional Organization for Standardizatior Not for Resale ISO 363-1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated Details of the sofware products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means. IsO's member body in the country of the requester. ISO copyright office Casepostale56.CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006 All rights reserved Not for Resale ISO 363-1:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technical committees.Each member body interested in a subjectfor which a technical committee has been non-governmental, in liaison with IsO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 %of thememberbodies casting avote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO363-1waspreparedbyTechnical Committee ISO/TC72,Textilemachinery and accessories SubcommitteeSc3,Machineryforfabricmanufacturing includingpreparatorymachineryandaccessories. This first edition of iSO 363-1 cancels and replaces ISO 363:1992, of which it constitute a technical revision. Iso 363 consists of thefollowingparts,underthe general title Textile machineryand accessoriesFlat steel healds with closed end loops: Part1:Dimensions ofhealdsmanufactured of rolledsteelwire Part 2:Dimensions ofhealds manufactured of hardened strip steel nal organization for standardizallon'ghts reserved ii Not for Resale CopyrightintematinalOganizatinfor Standardizaion Noreproductionornetworking emited withoutlicense fromHS Not for Resale ISO 363-1:2006(E) INTERNATIONALSTANDARD Textile machinery and accessories Flat steel healds with closed end loops Part 1: Dimensions of healds manufactured of rolled steel wire Scope 1 This part of isO 363 specifies the main dimensions of flat steel healds with closed end loops, manufactured of rolled steel wire for use in the textile industry. Dimensions 2 See Figure 1 and Table 1. 1 r networking permitted without license from IHS Not for Resale ISO 363-1:2006(E) Dimensions in millimetres 1 2 6 -10 a 1,5 (乙 /7) A-Ac. d 2 A 5 AL L-21 E-7≤l 7 b1 B-B° E/S h B 5'73 6 6 ≥1,6 Key straight healds SIMPLEX 1 2 cranked healds DUPLEX 3 end loop offset 4 thread eye a On some weaving machines, the transverse centreline of the thread eyes is at a distance of L/2 instead of (L/2)-10. b The healds can be ordered with corrugated end loops at the upper end and flat end loops at the lower end; such healds are recommended for USTER